Location: /Car Parking Sensors

Meta Targa SR2

Product Information

Easyfit parking sensors, mounted directly onto the rear bumper, this ingenious device detects obstacles to the rear of the vehicle making parking safer and easier. Especially useful for longer vehicles or vehicles with restricted rear vision. As the vehicle reverses towards an obstacle, an audible warning beep increases intensity to alert the driver until a constant tone gives the indication to stop before contact.

This must be the easiest to fit reversing aid on the market. No large holes to drill, just simply remove the number plate, mount the number plate bracket and clip the number plate back into the bracket.

Please note: Only suitable for European oblong type number plates and not the square types fitted to some Japenese Grey import vehicles. Also the number plate must be centrally fitted to the vehicle and not to one side. Not suitable for use with a tow bar or other obstructions in front of the number plate, see the Meta SR2 TGI which has the capability of programming out such obstructions. The SR2 can also be fitted to the front number plate area though an on/off switch may be required or a timer relay can be used for seamless operation more info

Easy two wire installation In most cases installation takes less than an hour Adjustable sensitivity Adjustable speaker volume Offset adjustability (how close an object is) Range from 0.3 to 1.5 Metres Easy two wire fitment No large holes to drill No painting/respraying Very discreet Front or rear mounting (a separate on/off switch may be required for front mounting)

Features:

Easy two wire installation
In most cases installation takes less than an hour
Adjustable sensitivity including offset (how close an object is before the units bleeps)
Adjustable speaker volume
Pickup range from 0.3 to 1.5 Metres
No large holes to drill (a small hole may be required to allow cable entry into vehicle)
No painting/respraying
Very discreet
Front or rear mounting (a separate on/off switch may be required for front mounting)
Made for all standard EEC approved number plates
External frame dimensions 11cm X 52cm

AutoExpress Test Review (4 Star rating)

More Information

Fitting Instructions

Please Note that Parking Sensor systems are designed to be a drivers aid and should not replace the need to drive carefully, and as such is designed as a safety enhancement device and is in no way intended as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when backing a vehicle. Always check surroundings for safety when backing.

This Standard SR2 is not compatible with the Display4 visual aid unit, if the Display4 is required please order the SR2 Tgi or the Frontplate4

**FAQ**
Question	Answer
Hi there, how long is the wire from the sensor to the controll box as it has to go from my number plate on the tailgate of my mitsubishi grandis to the bottom of the D pillar inside the car ? thank you	The leads from each of the sensors are a little over 3M in length. We can also supply a speaker extension lead if required. More info
is the speaker part of meta equipment where is it to be mounted.	The speaker is very small, not much larger than a two penny piece, it can be mounted anywhere, behind a carpet trim, on the rear hatch, anywhere you like.
I have a meta sri from but am about to fit a towbar can i uprate to a tgi without removing all present sensors	Yes the standard sensors will work with the TGI unit, but you'll have to upgrade the control box, the wiring loom and the speaker which are all different to the standard SR2 model, purchase a replacement here
Is there any maximum height restriction on mounting this ?	The maximum recommended working height is 1.5M
Are there any holes to be drilled into the car?	A small hole (6-8mm) may be required to allow the cables to enter the vehicle, a rubber bung is supplied with the kit to seal this hole.
Can this be fitted to the front of the car if so how does it operate	Yes the SR2 can be fitted to the front of the vehicle, a switch (not supplied) will be required to turn the unit on & off, or a timer relay can be installed which will operate the front sensors for a set period of time when the car is placed into reverse. More info We now supply a parking sensor kit specifically for the front of most vehicles More Info
Can the SR2 function with the Display4	No, the SR2 does not have an output for the Display4, if required please choose the TGi or Frontplate4 systems which are both compatible with the visual aid unit

Price: £99.00 £59.99

Add Product Review

Ask a Question

Product Code: ABP0060

In Stock: 3

Quantity: Add to Basket

Related Products

Meta SR2 speaker extension
£7.99

Meta FrontPlate 4
£109.00

Meta SR2 TGi Reversing Sensors
£119.00 £75.00

Meta SR2 Kit
£79.99

Meta Easypark
£79.99 £69.99

Gemel E662 Parking Sensors
£65.00

Customer Reviews

	Ray	2011-01-31
Very pleased with the Meta Targa SR2. Fitting on the Skoda Octavia took me a while as the wires had to fed up through the tailgate, but once installed it worked a treat. Top marks !

	Claire Cheshire	2009-07-16
Hubby bought one of these for my Golf. Absolutely brilliant will never back into a skip again.

	Steve Harris	2009-06-24
Been using the Meta reversing sensors for almost a year now. This really is a super simple item to fit, it looks good even better than some factory fit items fitted in the bumber, in actual fact you have to look hard to even notice them. Works brilliantly, not a single scratch on me rear. This item has definitely saved my marriage. Top product from a top supplier (this should guarantee a discount on my next purchase)